Doosan DX230LC-9C Fault Code E000110-00: Complete Diagnostic Guide

What is Doosan DX230LC-9C Fault Code E000110-00?

Fault Code E000110-00 indicates a communication error between the main Engine Control Module (ECM) and the Display Control Unit (DCU) on the Doosan DX230LC-9C excavator. This code specifically signals that the CAN bus communication network has detected an interruption or degradation in data transmission between these critical control systems.

The Doosan DX230LC-9C utilizes a Controller Area Network (CAN) protocol to enable real-time communication between the engine management system and the operator interface. When this communication link fails, the excavator's monitoring systems cannot properly relay engine parameters, potentially affecting performance monitoring and diagnostic capabilities. This fault is particularly critical because it can mask other developing issues and prevent accurate troubleshooting of the machine's operational status.

Common Symptoms

When Code E000110-00 is active, operators typically experience:

• Intermittent or complete loss of display information on the monitor panel, including engine RPM, coolant temperature, and fuel level readings
• Warning lights illuminating on the dashboard without corresponding fault conditions
• Inability to access diagnostic menus or view real-time engine parameters through the display
• Erratic gauge behavior, with readings fluctuating wildly or freezing at incorrect values
• Stored fault codes not displaying properly, even when other system malfunctions are present

Potential Causes

The most common technical causes for E000110-00 on used DX230LC-9C excavators include:

• Corroded or damaged CAN bus connectors at the ECM or DCU junction points, especially common in machines operating in wet or coastal environments
• Chafed or broken wiring harness near the main boom pivot point where the harness routes from the cab to the engine compartment—a known wear point on this model
• Faulty termination resistors within the CAN network causing signal reflection and data corruption
• ECM or DCU internal circuit board failures due to vibration damage or moisture intrusion over time
• Loose or oxidized ground connections affecting the communication circuit reference voltage
• Aftermarket monitor installations that improperly tap into the CAN network

How to Troubleshoot and Fix Code E000110-00

Step 1: Visual Inspection of Harness and Connectors

Begin by thoroughly inspecting the main wiring harness routing between the engine compartment and operator cab. On used DX230LC-9C excavators, check specifically where the harness passes through the cab floor grommet and near the swing bearing—these are common abrasion points. Look for chafed insulation, broken wires, or signs of rodent damage. Disconnect and inspect all CAN bus connectors (typically identified by twisted-pair orange and green wires) for corrosion, bent pins, or moisture intrusion.

Step 2: Electrical Testing with Diagnostic Tools

Using a digital multimeter, measure the CAN bus voltage between the CAN-High and CAN-Low terminals at both the ECM and DCU connectors with the key on, engine off. You should read approximately 2.5-3.5 volts DC. Next, check for proper termination resistance by measuring between CAN-High and CAN-Low with all power disconnected—you should read approximately 60 ohms (two 120-ohm resistors in parallel). Values significantly outside this range indicate open circuits, shorts, or missing termination resistors.

Step 3: Advanced Diagnostics with DX-Diag Software

Connect Doosan DX-Diag diagnostic software or equivalent J1939-compatible scan tool to the diagnostic port. Monitor live CAN bus traffic to identify whether the ECM or DCU is failing to transmit. Check the message error rate—excessive errors indicate network problems. For used machines, perform a wiggle test by gently moving harness sections while monitoring communication status to locate intermittent connection failures.

Step 4: Component Replacement and Verification

If testing reveals specific component failure, replace the affected ECM, DCU, or harness sections using genuine Doosan parts to ensure CAN protocol compatibility. After repairs, clear all fault codes and perform a complete system initialization using diagnostic software. Verify that all communication parameters return to normal ranges and that display functions operate correctly under various load conditions.

---

Disclaimer: This guide provides general diagnostic information for Code E000110-00. Hydraulic and electrical systems operate under high pressure and voltage. Always consult the official Doosan service manual for your specific serial number and consider professional diagnosis for complex electrical issues, especially on used equipment with unknown service history.